Questions/POLLS/Mentors Topic -  CZExtruder - the XXL model - QUESTIONS! (888 views) Notify me whenever anyone posts in this discussion.Subscribe
 
From: Eva (mejsel) DelphiPlus Member Icon Posted by host7/17/16 8:26 PM 
To: amyfb  (11 of 18) 
 71313.11 in reply to 71313.10 

Isn't it? And there are more options than shown, so you can continue experimentation. Stuffing the barrel with skinner blend bulls eye canes or even pattern canes can render fabulous results. 
Here's a cute little backgroundless flower cane from a white/red skinner blend bulls eye with yellow center pressed through the flower die from disk #6:
 

EVA

www.everclay.dk/

IF AT FIRST YOU DON'T SUCCEED
TRY, TRY AGAIN....

MY BLOGSPOT

MY ETSY

 

 

 
 Reply   Options 

 
From: amyfb7/31/16 10:08 PM 
To: Eva (mejsel) DelphiPlus Member Icon  (12 of 18) 
 71313.12 in reply to 71313.11 

I can hardly wait to try this! Very cool

 

 
From: Melody018/16/16 11:06 AM 
To: 7Jackie DelphiPlus Member Icon  (13 of 18) 
 71313.13 in reply to 71313.7 

Jackie, I've been following your extruder thread because I am also looking for an extruder that can be used with a drill. I followed the link to Cynthia Tinapple' s video, but it seems like the Bullens Wulliens adaptor for the of the Makins extruder is no longer available from the source listed. I did find the Bullens Wullens for sale at Etsy, but haven't make a decision yet. https://www.etsy.com/listing/242466646/bullen-wulliens-extruder-power-adapter?ref=listing-shop-header-1

If I get the silver Makins (Cynthia recommends using the PMC silver version of the Makins for easiest cleaning), the Bullens adaptor and the recommended vise it could get pricey. Hard decision. (edited: Just purchased the adaptor!)

I look forward to reading about your extruder quest.

Anita in AZ

http://www.etsy.com/shop/melodyodesigns/

http://www.melobeau.blogspot.com/

http://pinterest.com/anitalbrandon/

http://www.flickr.com/photos/melobeau/

http://www.facebook.com/MelodyODesigns/

  • Edited August 16, 2016 2:15 pm  by  Melody01
 

 
From: amyfb9/20/16 7:12 PM 
To: Melody01  (14 of 18) 
 71313.14 in reply to 71313.13 

The drill attachment for the Czechtruder is very nice to work with. I've got the plate c-clamped to the worktop, and i have it set to run very slowly to avoid stripping out the drive screw. I spend more time prepping the clay than extruding with only the stress of the holding the weight of the drill steady while she goes. (Try not to have to use that manly one from the shop; perfectly good lady-sized ones (bigger than a Drexel) are out there )

I do now wish I'd ordered the XXL model of the extruded from Lucy Clay. But, that said, compared to the silver one that costs $30 at any craft store - two of which I cranked right into the trash in a few short months -  this LC brand is worth every penny including freight from overseas. 

All the LucyClay stuff is awesome - ask for it for Christmas or your birthday, it's sooooo worth it. ;-0) (no affiliation, really I just love their stuff)

Cheerios

Amy

 

 
From: Jodie (jt_gmotu)9/23/16 1:30 AM 
To: amyfb  (15 of 18) 
 71313.15 in reply to 71313.14 

Amy,  

I got the big Lucy Clay slicer last year when my guild did an order, and I LOVE it. You can easily get slices of the same thickness...just an amazing tool.

Jodie

 

 
From: Melody019/23/16 8:58 AM 
To: amyfb  (16 of 18) 
 71313.16 in reply to 71313.14 
 

 
From: amyfb9/23/16 9:57 AM 
To: Jodie (jt_gmotu)  (17 of 18) 
 71313.17 in reply to 71313.15 

Hi Jodie,

Oh how I love my Lucy Clay Slicer. It just teases me non-stop to see how very tissue paper thin a slice I can make. Freeze the clay for 15 minutes first, if you don't already know that trick, and the results are AMAZING.

I tend to make small canes so every slice is like gold and I have very little scrap left over.

happy claying!

amyfb

 

 
From: Jodie (jt_gmotu)9/24/16 1:24 PM 
To: amyfb  (18 of 18) 
 71313.18 in reply to 71313.17 

Amy,

Yup! This is the slicer I was always hoping for....

Jodie

 

First Discussion>>

 
Navigate this discussion: 1-10 11-18
Adjust text size:
Using a mobile device? Switch to the Mobile Site.

Welcome, guest! Get more out of Delphi Forums by logging in.

New to Delphi Forums? You can log in with your Facebook, Twitter, or Google account or use the New Member Login option and log in with any email address.

Home | Help | Forums | Chat | Blogs | Advertising | Membership Plans
© Delphi Forums LLC All rights reserved. Privacy Policy. Terms of Service.