gatnerd

Military Guns and Ammunition

Hosted by gatnerd

This is intended for people interested in the subject of military guns and their ammunition, with emphasis on automatic weapons.

  • 3349
    MEMBERS
  • 190105
    MESSAGES
  • 2
    POSTS TODAY

Discussions

NGSW Phase 2 Consolidation and info   Small Arms <20mm

Started 30/8/19 by gatnerd; 522970 views.
roguetechie

From: roguetechie

15-Jun

You almost stumbled upon an idea I've been kicking around...

What if you have a potato masher/fn bullet thru style "rifle grenade" (only maybe a bit bigger) that has a single folded coaxial rotor which deploys the motor using a simple air speed sensor that kicks the rotor open as soon as it stops accelerating/gaining altitude from either being thrown or being launched.

By using a single coaxial rotor like that and not needing the full power to take off or start from a dead stop you could use a much smaller motor to charge size ratio giving you more flight time/range.

It could actually make for a decent little weapon

Apsyda

From: Apsyda

3-Jul

Apsyda said:

https://www.gao.gov/docket/b-420766.1

https://www.gao.gov/docket/b-420766.2

Both GAO protests were withdrawn by TV via Lone Star. As expected they didn't go anywhere in the end.

I suppose that means that SIG really did at least fit the standards asked for by the Army, if not definitely being the best rifle. Shame the protests didn't go further on the off chance some interesting trials info could have been released.

Gr1ff1th

From: Gr1ff1th

4-Jul

Well, time to commence the 3+ decade wait until we can FOIA the trial results to find out what really happened to the Textron entry, just like ACR before this

BruhMomento

From: BruhMomento

4-Jul

https://www.youtube.com/watch?v=WQnaTrLROCE

RAROG's plastic machine gun belts. useful for the future?

stancrist

From: stancrist

4-Jul

Ukraine's Plastic Machine Gun Belts -The Firearm Blog

Looks very useful for 7.62x54R, but it is a different link design than used with 7.62x51 and 6.8x51.

RovingPedant

From: RovingPedant

4-Jul

Pull-out rather than push-through does make more sense for plastic link. I’ve seen plastic M13 link but apparently it’s not as robust as the metal. Not really a surprise.

stancrist

From: stancrist

18-Jul

The US Army's new Belt fed Machine gun. The M250 is replacing the M249

Thanks to Established Titles for sponsoring this video! Get 10% off on any purchase with code GARANDTHUMB. Go to https://establishedtitles.com/GARANDTHUMB an...

Msg 7519.2913 deleted
gatnerd

From: gatnerd

27-Jul

If your M14 flashbacks werent already in effect, I present: SIG working to develop a stamped steel magazine for the NGSW.

https://soldiersystems.net/2022/07/25/sig-sauer-develops-in-house-magazine-production-capability/

In the comments, Eric of SSD mentions that the 6.8 projectiles are being harsh on the Lancer mags, which may be a reason for this. Although how they would be worse than M855A1, or how relatively soft steel would be much better against Hardened steel / Tunsgten, is an open question.

A loaded M14 mag was 1.5-1.62lbs depending on source...

stancrist

From: stancrist

27-Jul

gatnerd said:

In the comments, Eric of SSD mentions that the 6.8 projectiles are being harsh on the Lancer mags, which may be a reason for this. Although how they would be worse than M855A1, or how relatively soft steel would be much better against Hardened steel / Tunsgten, is an open question.

Other possible reasons for SIG developing in-house magazine production:

- Eliminate reliance on Lancer.

- Increase SIG profits.

TOP